<div dir="ltr"><div><div dir="ltr">On Wed, Jan 9, 2019 at 9:42 PM Andrew Kohlsmith (mailing lists account) <<a href="mailto:aklists@mixdown.ca">aklists@mixdown.ca</a>> wrote:<br></div><div class="gmail_quote"><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div style="overflow-wrap: break-word;"><div><blockquote type="cite"><div>On Jan 9, 2019, at 9:03 PM, Khalid Baheyeldin <<a href="mailto:kb@2bits.com" target="_blank">kb@2bits.com</a>> wrote:</div><div><div dir="ltr"><div class="gmail_quote"><div>The reason I suspect bad connections is that I changed the controller to a backup</div><div>board that I have. Same result. Then other RJ45 cables. Same result. <br></div></div></div></div></blockquote><div><br></div>If you can, throw the motors and mechanicals in your deep freeze for a few hours and then, inside where it’s warm, try to operate it.</div></div></blockquote><div><br></div><div>Not possible. The motors are mounted inside the scope housing. <br></div><div><br></div><div>Here is <a href="https://www.youtube.com/watch?v=tgzy1bFrGBc&list=PLZukVlnRom-3YhPkIIvXWJqaCuHc1_qj5">how it looks like in action</a> (without the actual optical tube on it, or the counterweights).</div><div>The only thing that may have changed are the RJ45 cables.<br></div><div><br></div><div>Tomorrow has a high of -8C and it is dry. So may take the scope out and try it on the patio to see if the symptoms are the same. <br></div><div><br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div style="overflow-wrap: break-word;"><div> <br><blockquote type="cite"><div dir="ltr"><div class="gmail_quote"><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">What about the stepper drivers, are they marginally sized and higher current required for stepping in cold temperatures is causing them to fault?<br></blockquote><div><br></div><div>They are tiny. NEMA 11 instead of the usual NEMA 17. But they have an 18:1 <br></div><div>gearhead which gives them enough torque, and there are others who are using</div><div>the same model of motors without issues (not in sub zero temperatures though).<br></div></div></div></blockquote><div><br></div>Any grease or other lubricant used in the gearboxes which may become stiff or become more viscous in the cold?</div></div></blockquote><div><br></div><div>That is theoretically possible, but I doubt it. This mount is made in Japan and they probably make sure it would work in low temperature. Also, I bought the scope from someone in town, and probably he would have been using it in low temperatures. <br></div><div> <br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div style="overflow-wrap: break-word;"><div><br><blockquote type="cite"><div dir="ltr"><div class="gmail_quote"><div>I did buy the flat RJ45 cables and the sockets, from eBay, so they may not be the best </div><div>out there.  But they are the flat ones, which are the most flexible. <br></div></div></div></blockquote><br></div><div>Mine come from Sayal, which I’m sure is also very poor quality. I guess if you had a way to perform a cable test in the cold it would make quick work of this theory. </div><div><br></div><div>If it’s skipping and generally misbehaving and you go out and shove the cable into the socket, holding it there while retesting, does it still skip?</div></div></blockquote></div></div><div><br></div><div>It is not practical since the scope is moving all the time (either at the rate of earth's rotation, or faster when changing positions in the sky).</div><div><br clear="all"></div><div>I tested the 5A power supply and it worked well (no surprise there). <br></div><div><br></div><div>Will test the same power supply out doors tomorrow. <br></div></div>